Diametri / imballo
Diametri |
Can 22,7 kg |
---|---|
4,8 x 350 mm (3/16 x 14 in) | ED012845 |
DETTAGLI
Caratteristiche
- Scoria sottile per una minima interferenza dell'arco
- Penetrazione elevata
- Bagno di fusione visibile e pulito
- Controllo superiore del bagno di fusione
Applicazioni tipiche
- Tubo in silicone
- Tubo API 5L di grado da X56 a X70
- Tubo cross country e interno all’impianto
Posizioni di saldatura
- Tutte
Gas di schermatura
- Non applicabile
Caratteristiche speciali
- Recommend to switch to Pipeliner® Arc 80 for superior puddle control and visibility
Informazioni sui servizi
Documentazione
Potresti anche aver bisogno di
BEFORE USE, READ AND UNDERSTAND THE SAFETY DATA SHEET (SDS) FOR THIS PRODUCT AND SPECIFIC INFORMATION PRINTED ON THE PRODUCT CONTAINER. Pagina di ricerca SDS
Vedere il risultato del test esclusione di responsabilità
CONFORMANCE
CONFORMANCES | SPECIFICATION | CLASSIFICATION |
---|---|---|
AWS | AWS A5.5 | E8010-G, E8010-P1 |
ISO | ISO 2560-A | E 46 4 1NiMo C 2 5 |
ABS | AWS A5.5 | E8010-G |
CWB | CSA W48 | E5510-G |
MECHANICAL PROPERTIES
Classification |
Yield Strength @ 0.2% Offset
MPa (ksi) |
Tensile Strength
MPa (ksi) |
Elongation
% |
Charpy V-Notch
J (ft-lbs) @ -30°C (-20°F) |
Charpy V-Notch
J (ft-lbs) @ -45°C (-50°F) |
Hardness Rockwell B |
---|---|---|---|---|---|---|
E8010-G Requirement | 460 (67) min. | 550 (80) min. | 19 min. | |||
Typical Result, As-welded | 470-570 (68-83) | 570-660 (83-96) | 20-26 | 57-89 (42-66) | 32-68 (24-50) | 87-95 |
DEPOSIT COMPOSITION
Classification | %C | %Cr | %Cu | %Mn | %Mo | %Nb | %Ni | %P | %S | %Si | %V |
---|---|---|---|---|---|---|---|---|---|---|---|
E8010-G Requirement | 0.30 min. * | 1.00 min. * | 0.20 min. * | 0.50 min. * | 0.03 max. | 0.03 max. | 0.80 min. * | 0.10 min. * | |||
Typical Result | 0.13-0.17 | 0.13 max. | 0.06 max. | 0.55-0.95 | 0.10-0.42 | 0.010 max. | 0.63-0.81 | 0.01-0.02 | 0.01 max. | 0.06-0.16 | 0.005 max. |
TYPICAL OPERATING PROCEDURES
Diameter | Polarity |
Current
Amps |
---|---|---|
1/8 in (3.2 mm) | DC+ | 75-130 |
5/32 in (4.0 mm) | DC+ | 90-185 |
3/16 in (4.8 mm) | DC+ | 140-225 |
NOTES
Note |
---|
* To meet the requirements of a "G" classification, the chemical composition of the weld deposit must meet the minimum requirement for one or more of these elements. |